EE4090工程实习

这门课学什么

课程概述与目标

Students will gain practical experience under the Industrial Attachment Scheme (IAS) / Overseas Internship Scheme (OIS) (Part A) or the in-house training scheme (Part B). Part A (Industrial Attachment Scheme (IAS) / Overseas Internship Scheme (OIS) Students will gain practical work experience and / or learn new technologies from an industrial / research environment while their spirit of professionalism will be nurtured. Part B (In-House Training) Students will undergo comprehensive practical training in computer and data engineering, electrical and electronic engineering, information engineering, and microelectronics engineering. In particular, students will gain valuable hands- on experiences that complement the theoretical knowledge acquired through their taught courses.

教学内容（Keyword Syllabus）

Part A: Industrial Attachment Scheme (IAS)/ Overseas Internship Scheme (OIS) Structure and Content Students are required to undergo a six-week IAS or nine to thirteen-week OIS training in a company or research institute that is relevant to the electronic, electrical, computer, or IT industry. The duration of the training for each student is contingent upon the availability of engineering training programs offered by the respective company or research institute. Supervision and Assignment A mentor from the company or research institute will be assigned to provide guidance, advice, and assess the student's performance throughout the training period. Additionally, academic staff members from the Department of Electrical Engineering at City University of Hong Kong will be appointed as co-supervisors to monitor the student's progress. Students are expected to maintain a weekly logbook to document their work and activities. The assessment will be based on the logbook entries as well as the overall performance of their assigned tasks. Before the completion of the training, students will be required to deliver a presentation on their work. Part B: In-house Training Students are required to complete two out of the following four modules, which encompass practical training in electrical and electronic systems, computer hardware and software, computer system administration, and networking: Electrical, Electronics and 3D Drawing Workshop Design circuit layouts for electrical and electronic sub-systems; Utilize Altium Designer, a PCB design software; Integrate and solder a PCB circuit board; Create 3D drawings using DesignSpark Mechanical; Gain knowledge of basic electrical installation practices; Understand MOS transistors through SPICE simulation. Raspberry Pi and IoT Set-up, configure a Raspberry Pi computer system and develop IoT applications based on its hardware and software. Computer System Administration Set-up and configure Linux and Window systems according to specific requirements. CCNA Networking Set-up, configure, test, and monitor a network according to specific requirements.

校方 PDF 第 4 页 · Keyword Syllabus

预期学习成果

查看学习成果表

CILO	预期学习成果	比重	DEC
1	Describe practical working experience gained from an industrial / research environment	—	DEC-A1, DEC-A2
2	Discuss the importance of the spirit of professionalism and professional ethics in a real-life environment	—	DEC-A1
3	Describe the technologies used in a modern industrial / research setting	—	DEC-A2
4	Communicate their ideas and present their work effectively	—	DEC-A1, DEC-A2
5	Describe practical experience gained from an in-house environment	—	DEC-A1, DEC-A2
6	Apply proper engineering tools and analysis techniques to solve real-world problems	—	DEC-A2
7	Describe the technologies used in a modern industrial setting	—	DEC-A1
8	Communicate their ideas and present their work effectively	—	DEC-A1, DEC-A2

校方 PDF 第 2 页 · Course Intended Learning Outcomes (CILOs)

我能不能修这门课

先修、建议先备和并修要求分别查看；等同及互斥条件也会影响选课。and 表示同时满足，or 表示备选；组合条件按下方原文分组阅读。

先修条件

(EE2000 Logic Circuit Design or EE2301 Basic Electronic Circuits or EE2005 Circuits and Devices I) and CS2311 Computer Programming The above pre-requisite requirements only apply to Part B In-house Training.

建议先备知识

无（校方注明 Nil）

并修要求

该版官方课纲未列明该项。

其他修读要求

该版官方课纲未列明该项。

等同课程及条件

EE4091 and EE4092 or EE4093 and EE4095 or EE4096 and EE4097 or EE4290 and EE4291

互斥课程及条件

无（校方注明 Nil）

怎么考，怎样才算通过

考核方式

Continuous assessment: 100%; Examination: 0%

各项考核占多少分

考核项目	比重	生成式 AI 使用	备注与限制
Part A (IAS/OIS) and Part B (In-House Training)CILO 1, 2, 3, 4, 5, 6, 7, 8	100%	是（Yes）	Part A: CILO 1-4: Log-book 34%; Demonstration and Presentation 33%; Co-supervisors comments 33%. Part B: CILO 5-8: Continuous Assessment 100%; refer to the additional document titled EE4090 Assessment Components for In-House Training for further information.

校方 PDF 第 3 页 · Assessment Tasks / Activities (ATs)

校方课纲说明 Part B（In-House Training）须参阅另一份《EE4090 Assessment Components for In-House Training》。目前未能从已查阅的校方来源取得该文件，因此 Part B 的具体考核项目尚不完整。

查看校方原始考核表与使用要求

Combined printed AT row: Part A (IAS/OIS) and Part B (In-House Training); CILOs 1-8; 100%; GenAI Yes. Part A CILO 1-4 weights: Log-book (34%), Demonstration and Presentation (33%), Co-supervisor comments (33%). Part B CILO 5-8 Continuous Assessment: 100%; see attached EE4090 Assessment Components for In-House Training document.

通过条件

Part A: The assessment is based solely on a pass/fail criterion. In order to pass the course, students must successfully complete the training with satisfactory performance, as recommended by the training mentor and the CityU co-supervisor. Part B: Please refer to the attached document titled "EE4090 Assessment Components for In-House Training" for further information.